000 | 02842nam a2200337 a 4500 | ||
---|---|---|---|
003 | OSt | ||
005 | 20220212155442.0 | ||
008 | 070518s19uu xx 00 eng d | ||
040 | _cCvSU Main Campus Library | ||
041 | 0 | _aeng | |
082 | 0 | 4 |
_a629.23 _bB32 2006 |
100 | 1 | 0 |
_aBatino, Jade Micole S. _eauthor |
245 | 1 | 0 |
_aDevelopment and construction of an improvised hydraulic press / _cby Jade Micole S. Batino, Eugenia P. Profeta Jr., and Romel I. Macalindong. |
260 | 0 |
_aIndang, Cavite: _bCavite State University- Main Campus, _c2006. |
|
300 |
_axix, 72 pages : _billustrations ; _c28 cm. |
||
336 |
_2rdacontent _atext |
||
337 |
_2rdamedia _aunmediated |
||
338 |
_2rdacarrier _avolume |
||
500 | _aDesign Project (BS Industrial Technology Major in Automotive Technology) Cavite State University. | ||
504 | _aIncludes bibliographical references. | ||
508 | _aCollege of Engineering, and Information Technology (CEIT) | ||
520 | 3 | _aBatino, Jade Micole S., Macalindong, Romel I. and Profeta Eugenio P. Jr., Development and Construction of an Improvised Hydraulic Press. Bachelor of Industrial Technology major in Automotive Technology. Cavite State University, Indang, Cavite April 2005. Adviser: Eduardo J. Llanita The Development and Construction of an Improvised Hydraulic Press was conducted in Tres Cruzes Tanza, Cavite. It was tested and evaluated at the College of Engineering and Information Technology on February 6 to 16, 2006. The study was conducted to show that it is possible to fabricate a Hydraulic Press that is low cost and can match the performance of commercially available pressing machine. The system has three major parts: the frame, the hydraulic jack and spring. The frame of the machine consists of posts, ram, and base. The machine design can be used as an alternative from commercially available pressing machine. Also it is a good instructional material in acquainting students on else of the press. The machine approximately weighs 400 kilograms and can release 15 tons of force needed to press fitted parts. Maximum stroke of the jack reaches approximately nine inches. The total cost of the project was Php. 28, 505. The only problem observed during testing is in adjusting the ram. It is recommended to install a motored pulley for easy adjustment of the ram. | |
541 |
_d06/16/2006 _eDP-206 _cSubmitted to the University Library |
||
650 | 0 |
_aAutomobiles _xEngines. _94433 |
|
690 |
_946 _aBachelor of Industrial Technology _xAutomotive Technology |
||
700 | 1 |
_aProfeta, Eugenio P., Jr. _eauthor |
|
700 | 1 |
_aMacalindong, Romel I. _eauthor |
|
700 |
_aLlanita, Eduardo J. _98761 _eadviser |
||
856 |
_yClick here to view the abstract and table of contents _uhttp://library.cvsu.edu.ph/cgi-bin/koha/opac-retrieve-file.pl?id=e1eddef811b292cd2810a82ab0a8ed85 |
||
942 |
_2ddc _cMAN |
||
999 |
_c1279 _d1279 |